| ELECTRICAL ERROR ANGULAR RANGE IN MINUTES | -7.0 TO 7.0 |
| ACTUATOR FRICTION TORQUE AT PLUS 25 DEG CELSIUS | 0.20 INCH-OUNCES MAXIMUM |
| AFT OF FIRST FLANGE DIAMETER | 1.9985 INCHES MINIMUM AND 1.9995 INCHES MAXIMUM |
| BODY DIAMETER | 1.9900 INCHES MAXIMUM |
| BODY MATERIAL | STEEL CORROSION RESISTING |
| BODY SIZE | 23 |
| BODY STYLE | STANDARD ROUND D |
| FLANGE DIAMETER | 2.2490 INCHES MINIMUM AND 2.2500 INCHES MAXIMUM |
| FLANGE THICKNESS | 0.2500 INCHES NOMINAL |
| FRAGILITY FACTOR | MODERATELY RUGGED |
| FREQUENCY IN HERTZ | 400.0 NOMINAL |
| OVERALL LENGTH | 4.5490 INCHES NOMINAL |
| MAXIMUM FUNDAMENTAL NULL VOLTAGE IN MILLIVOLTS PER VOLT | 30.00 OUTPUT |
| MAXIMUM TEMP RISE | 30.0 CELSIUS |
| MAXIMUM TOTAL NULL VOLTAGE OUTPUT IN MILLIVOLTS PER VOLT | 20.00 |
| MOUNTING SURFACE TO TERMINAL END DISTANCE | 3.8300 INCHES MINIMUM |
| PHASE SHIFT ANGLE IN DEG | 2.000 INPUT TO OUTPUT NOMINAL |
| PILOT LENGTH | 0.0430 INCHES NOMINAL |
| PILOT DIAMETER | 0.5950 INCHES NOMINAL |
| SECOND SHOULDER DIAMETER | 1.9985 INCHES MINIMUM AND 1.9995 INCHES MAXIMUM |
| SECOND SHOULDER LENGTH | 0.1700 INCHES NOMINAL |
| SHAFT DIAMETER | 0.2402 INCHES MINIMUM AND 0.2405 INCHES MAXIMUM SINGLE SHAFT |
| SHAFT LENGTH | 0.7190 INCHES NOMINAL SINGLE SHAFT |
| SHAFT THREAD CLASS | 2A SINGLE SHAFT |
| SHAFT THREAD DIRECTION | RIGHT-HAND SINGLE SHAFT |
| SHAFT THREAD LENGTH | 0.2900 INCHES NOMINAL SINGLE SHAFT |
| SHAFT THREAD SERIES DESIGNATOR | UNF SINGLE SHAFT |
| SHAFT TYPE | SPLINE W/THREADS SINGLE SHAFT |
| SHAFT NOMINAL THREAD SIZE | 0.250 INCHES SINGLE SHAFT |
| SHOULDER DIAMETER | 1.9850 INCHES MINIMUM AND 1.9900 INCHES MAXIMUM |
| SPECIFICATION/STANDARD DATA | 81349-MIL-S-20708/47 GOVERNMENT SPECIFICATION |
| SPLINE TOOTH QUANTITY | 22 SINGLE SHAFT |
| SPLINE TOOTH DIAMETRAL PITCH | 96 SINGLE SHAFT |
| STATOR INPUT CURRENT RATING | 285.0 MILLIAMPERES MAXIMUM |
| STATOR INPUT ELECTRICAL POWER RATING | 2.2 WATTS NOMINAL |
| STATOR INPUT VOLTAGE RATING IN VOLTS | 90.0 NOMINAL |
| ZRS IMPEDANCE ANGLE IN DEG | 45.00 MINIMUM AND 50.00 MAXIMUM |
| ZRS IMPEDANCE MAGNITUDE IN OHMS | 37.00 MINIMUM AND 50.00 MAXIMUM |
| ZSO IMPEDANCE ANGLE IN DEG | 82.50 MINIMUM AND 85.50 MAXIMUM |
| ZSO IMPEDANCE MAGNITUDE IN OHMS | 275.00 MINIMUM AND 340.00 MAXIMUM |
| TERMINAL LOCATION | REAR |
| TERMINAL TYPE AND QUANTITY | 6 SCREW |
| TEST DATA DOCUMENT | 81349-MIL-S-20708 SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| TRANSFORMATION RATIO | 1.154 ROTOR TO STATOR NOMINAL |